Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
Just how do you actually feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a new one is also a moderately difficult project. If the old tub is readily easily accessible, the project can move immediately; if you have to open a wall surface to remove the old bathtub and position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the new one. Ensure you have certified on your own for the job as well as are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This short article will help you set up a new bath tub in your shower room if you have actually already acquired a new bathtub and also don't need to alter the arrangement of your previous water pipes.
Your tools and product list ought to comprise the following:
Planning for the Installment
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the faucet features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be rather problematic because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, put the tub in the called for position. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out level.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water and inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bath tub as well as additionally inspect the overflow outlet and also the regular outlet for leaks.
Finally, fix the bath paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bath tub should wait until the tub has been utilized at the very least once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in issues with wetness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealer can break relatively very early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently available on the market. It is suggested to fit the ceramic tiles using water-resistant or waterproof sticky and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a devoted reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that excerpt was valuable. Sharing is good. You won't know, you will be doing someone a favor. We thank you for reading our article about Installing A Bathtub.
Fix it today! Report this page